Showing posts with label Pool Pump Problems. Show all posts
Showing posts with label Pool Pump Problems. Show all posts
Saturday, July 13, 2013
Salt Water Pool
A salt water or saltwater pool is a swimming pool which is filled with a mild salt solution. Many companies which install pools can construct salt water pools and outfit them with the necessary sanitization systems, and these pools can vary radically in size from small lap pools to large community pools used for recreation. Swimmers sometimes enjoy saltwater pools because the water feels softer and gentler than that in some other types of pools.
Salt water pools are not chlorine free, but it is not necessary to add chlorine to the pool. Instead, using a device known as a chlorine generator, the pool makes its own chlorine products for hygiene though electrolysis which breaks down the salt. Periodically, salt must be added to the pool to keep the salt solution strong enough for the chlorine generator to work. When a salt water pool is maintained properly, it should stay clean and safe to use, and it lacks the strong odor associated with chlorinated pools.
Setting up a salt water pool can be expensive, as the chlorine generator and associated equipment can be costly. However, the salt used is significantly less expensive than chlorine additives for pools, which can save money in the long term. The pool will also require cleaning and maintenance, just like any other pool, and people who use pool services may want to confirm that their service is accustomed to working with salt water pools.
People can install salt water pool systems in existing pools or they can install a brand new pool with a salt water system. The chlorine generator produces enough chlorine to inhibit the growth of bacteria, although the pool can still develop algae which needs to be cleared with a filtration system. Filtration will also clear leaves, debris from the bodies of swimmers, and other materials. Consumers concerned about pool hygiene who dislike the caustic nature of traditionally chlorinated pools may choose a salt water pool as an alternative which is more pleasant to swim in. Others simply enjoy swimming in saltwater.
Consumers attached to municipal water and sewer systems may want to check with local authorities about regulations concerning salt water pools. Some municipalities ban the connection of salt water pools to the sewer system, or require people to treat the pool water before draining it into the sewer. A pool installation company should be able to provide consumers interested in salt water pool installation with more information and recommendations.
For More Help Go To www.poolhelpusa.comBlue Wave NA390 Standard Pool (Google Affiliate Ad)Intex 57435EP Whale Spray Pool (Google Affiliate Ad)
Saturday, December 29, 2012
PUMP PROBLEMS
Pool Pump Problems
Pump Running But Not Pumping Water (or not enough flow)
One of the main pool pump problems I hear from customers is" the pump is running but it’s not pumping any water". This is because the pump is not "primed" or at least not primed fully. When the pump is primed, it means the water is flowing through the pump at top speed, creating suction and pressure. Here’s a few of the MAIN causes of a pump not being fully primed or primed at all:
1) The water level has dropped below the skimmer level and the pump is sucking air-or, if you have a weir flap in the skimmer it may get stuck in the closed or up position. (Also, if you have a skimmer basket with a round weir that bobs up and down inside, if the basket gets full of leaves it may get stuck in up position cutting off water flow).
2) Possibly the pump lid is not on tight or needs a new or cleaned/lubricated o-ring
3) If the pump has a closed face impeller , possibly debris has gotten past the pump basket (maybe broken basket?) and clogged impeller.....or, impeller shaft may be broken and the motor is spinning but NOT the impeller.
4) The plumbing going to your pump may be clogged
5) If you have a check valve on the inlet side of pump, part of it may have broken off and is blocking inlet
6) The inlet or outlet plumbing of pump has become loose, causing an air leak (often due to PVC pipe shrinking because pump ran dry and heated plumbing)
7) A diverter valve in front of pump is leaking air (through stem and/or cap o-rings)
8) The ceramic shaft seal is leaking water and/or air
9) Most pumps have a threaded plug before and after the impeller on the lower side (usually right side) of pump-these small plugs(about 1/4 inch) may come loose, letting in air.
10 )If you have just installed a new pump or motor or the pool was drained or any plumbing has been redone or for any reason air has gotten into your plumbing line you may need to force water through your plumbing from the skimmer to the pump to remove air....this can be done with a device called a "drain jet" (shown below) that is available from a hardware store....it can also be used in reverse FROM the pump TO the skimmer to fix problem #4 above!...AND possibly FROM skimmer TO pump while pump is off to find air leaks for problems #5,6,7,8 and 9 above!
11) If your pump has a problem catching prime AFTER cleaning the pump basket, try installing a swing check valve in front of pump.
12) If pump is 230 voltage, is it running on only 115 volts?
13) Dirty filter?
Drain jet which is a canvas "balloon" that attaches to water hose and forces water down pipe - below that is more common rubber version.
Pump Making Excessive Noise
1) Most often this is due to bearings in motor failing
2) Sometimes a blockage such as a filter backwash in the halfway position can cause excessive noise
3) Sometimes the motor endbells can wear out letting the bearings oscillate inside creating a rhythmic noise(more on this in motor section)
Capacitors shown below with microfarad value (uF) highlighted in orange. The smaller capacitor is for a 1 HP or smaller motor, the larger capacitor is for a 1.5-2 HP motor
Motor Stuck - Hums Then Trips Breaker or Just Shuts Off
1) Most likely a bad capacitor(shown above),which is located on the top of most motors under rounded cover and sometimes on the end of motor...it can be checked by an ohm meter - the correct reading would be a drop to zero followed by a slow rise in resistance. If you replace capacitor, the capacitor should be of the same value or at least within a few percent of value of microfarads (MFD or uF symbol on capacitor)
2) Stuck impeller usually due to debris caught in impeller, but can also be caused by calcium build up from leaking seal-to check, try turning motor shaft or impeller by hand with power off to see if impeller is stuck
Sometimes if you have an air leak somewhere in equipment, after pump shuts off the flow of water may reverse causing debris from filter to back up into the pump impeller. When the pump tries to start the following day, the motor cannot overcome the friction of debris to start. This may be a very slow process, perhaps hours after pump shuts off.
3) Motor has improper voltage or is simply old and start winding is burnt out
4) The bearings have seized
5) Also, a thermal overload switch will just shut off pump if it overheats.
Problems unique to two speed pumps
1) Pump starts in low speed but will not start in high speed or go to high speed - this can be caused by a capacitor which is partially damaged (it has enough power to start at low speed and perhaps even go to high speed with the inertia, but cannot start at high speed). After changing capacitor, try running pump at night when its cooler to get a longer capacitor life.
2) Pump starts in high speed but NOT in low speed...usually caused by obstruction (debris on/around/in impeller)- the pump does not have enough torque to overcome friction on low speed...clean out pump impeller and surrounding area, check for cracks in pump basket.
2-speed pumps should be started in high speed for a few minutes to catch prime and avoid the problem above...in fact most utility companies require some of two speed controller to be eligible for rebate programs, which offer automatic switching to low speed after catching prime.
PLEASE VISIT US AT WWW>POOLHELPUSA>COM
Subscribe to:
Posts (Atom)