Showing posts with label Clean Up A Green Pool. Show all posts
Showing posts with label Clean Up A Green Pool. Show all posts

Sunday, September 15, 2013

Top 5 Pool Pump Problems

Top 5 Pool Pump Problems Pump problems The pump is one of the most important parts of your pool's plumbing system. It is responsible for creating pressure in your pool, which forces the water to flow through the filter. Think of it as the heart of your swimming pool and without a filter pump your pool will rapidly become a pond of scum. Unfortunately sometimes your pool pump will not work due to one of many issues that might occur. In this article. #1 The pump does pull water. If your pump is not moving water you first want to check the skimmer and pump baskets and make sure they are empty as not to restrict water flow. Next make sure your pool filter is clean. Once you have checked these, you may want to check the pump impeller. This is the part in the pump that is connected to the motor that moves the water. Impellers will clog from time to time, especially during the springtime. To inspect the impeller, you will need to open the pump, to see inside of the impeller housing or volute. One of the major causes for pump suction loss is an air leak in the suction line. The suction line is where the pump gets supplied with the water from the pool. You will know this may be the issue if your pump will not catch prime. Prime is when your pump is running at full capacity. A pump is designed to suck water, but it can and will suck air if given the chance. Air has less mass than water, so a pump will suck air before it will suck water. If you think you have an air leak, see #5 below. #2 The pump is leaking water go-kits for pool pumps If you see a pump leaking water it will be on what we call the pressure side. This is after the pump lint pot ( the pot and anything before is not under positive pressure but rather negative pressure or suction and will not leak but try to draw in air see #1). The causes for a leak can be a bad impeller housing o ring, bad shaft seal, or bad thread sealant or shrunken threads on the plumbing discharge pipe, or the pipe that comes out of the pump. If it is an o ring or seal it is best to get what they call a Go Kit, which has every seal and oring in the pump, in one kit. I always say, if you are going to take the pump apart, you might as well replace all the seals. Pool Pump Go-Kits cost about $20, depending on the pump model and are cheaper than buying all the seals one by one. #3 The motor will not work or turns off after time.pool pump motor capacitor There can be many things that can cause this issue. You want to start by checking for power to the motor. Check your breaker and make sure your timer is set to turn on the pump. If you are getting power, the next thing to check for is sounds. Can you hear the motor hum or can you hear a click? A humming motor can mean it is the capacitor. Think of the capacitor as a battery (looks like one too) that jumps the motor to start spinning. A capacitor stores up a quick jolt of electricity to start the motor. They can be located in the back of the motor housing or in a hump on the top or side of the unit. If your motor runs but turns itself off after a time, it may be over-heating. Pool pumps use a lot of wattage and need a constant supply. If it is in the middle of a hot day and everyone in your neighborhood has the AC on high there may be a drop of power causing the motor to overheat. Not much you can do at that point but maybe run your pump at night when it is cooler. The second leading cause for this is motor fan failure or vent blockage. On the underside of the motor are vents that can get clogged up with dirt and leaves.pool motor cover Make sure you do not have dirt build up and keep them open and clear. I have run across cases where was just plain old sun light causing the motor to overheat. This is common in the south west and I would recommend getting a motor cover to keep the sun at bay. #4 The motor/pump is making a loud noise. Everyone (and their neighbors) hates a loud swimming pool pump. If your pump is loud, the first thing to do is to listen to it. What kind of sound does it make? If it sounds like there are rocks in it, this can be from it vibrating on the pad it sits on, or it could be cavitation. A piece of rubber mat under it might help to stop the noise. If that is not the case, it may be cavitation. Cavitation happens when the pump cannot get enough water fast enough, or the pump is "starved for water". The pump impeller is spinning too fast with not enough water and starts to beat the air molecules out of the water. If you didn't just install an oversize pump, you will want to check the lines for a clog, or a closed valve. In some cases it may be a clogged filter or impeller. Clear out any obstructions and you should be fine. Now if you pump is screaming (this is what sets off the neighbors) your motor may need new bearings. Bearings are mounted on the pool motor bearings pool motor shaft inside the motor to help reduce the friction as the electro magnates make the motor shaft spin. This is a high wear and tear item within the motor. Although the bearings are cheap (about $15) the labor is intensive. Most motors have 2 different sizes in them and usually take special bearing pullers to remove them. I always recommend taking the motor to a shop and for about $100 you can get a motor refurbished. #5 The motor/pump is sucking in air. Pool pumps are supposed to be air tight. With a clear pump lid, you "should" see no air in the pump basket. This is rarely the case however, small air leaks are common. When the air leak gets too large, however, it can create problems with circulation or keeping the pump primed. The most common causes of a pump air leak include bad thread sealant where the pipe enters the pump, a leaky valve stem on one of the suction valves or a break in the plumbing. Other sources of air leaking into the system include a loose or old pump lid or pump lid o-ring or an ill fitting pump drain plug. All air leaks originate BEFORE the impeller.lemon lime is optional! A good test to locate an Air Leak, and it will sound funny - is to use shaving cream (not gel). Spread the shaving cream over the suction side joints and fittings with the pump on. The pump will try to suck the foam into the pipe because it has less resistance or mass then the water. At the air leak you will start to see the layer of foam dimple as it gets sucked into the system revealing where the leak is. At this point you will know what part needs to be repaired or replaced. So, there you have it - some of the most common reasons for pool pump aggravation. We hope to have helped you through yours!

Saturday, August 24, 2013

Types of Pool Algae

Types of Pool Algae Nearly every pool owner has had to deal with algae problems at one time or another. Even with a properly-working filtration system, sanitizers at their recommended levels, and a watchful eye, algae blooms can still develop. Algae spores can enter a pool in a variety of different ways, but is most commonly introduced into a pool through wind, rain, dirt, and even on a swimmer’s body or bathing suit. Keeping algae spores out of your pool is impossible, so it is important to prevent the microscopic spores from turning into unsightly algae blooms. Maintaining clean, algae-free water will help keep your pool and your family happy and healthy, Although there are over 20,000 known species of algae, there are only a few types that of algae that can survive and grow inside the sanitized environment of a swimming pool. Below are the kinds of algae that you might run into in your pool:
Green Algae
This is the most common type of pool algae. Green algae can show up either as discolored spots on your pool wall, or, more commonly, as large floating masses on the pool surface. While not particularly difficult to get rid of, green algae grows very quickly, so if left untreated, it can multiply to cover large areas of pool walls and surfaces.
Algae Pool Pink
Pink algae isn’t really algae at all, but a type of fungus known as Paecilomyces Lilacinus. The fungus forms into small colonies on pool surfaces, and can easily be eliminated through brushing and chlorination.
Black (Blue-Green) Algae
This is the toughest and most resistant type of algae, and it shows up as small, dark spots on the pool walls. Black algae is extremely difficult to get rid of because it buries its roots deep down in the plaster or tile gout, and will continue to grow back as long as the roots remain intact. Black algae also requires a mix of powerful chemical and vigorous, repeated brushing to eliminate.
Algae Pool Yellow Mustard Algae
Typically looks like small deposits or sand or dirt, and is usually found in the shady parts of the pool, and on pool steps and equipment like lights or ladders. Mustard algae is resistant to normal chlorine, so it requires a mix of powerful chemicals and vigorous, repeated brushing to eliminate. Over 27000 pool items to make pool care easy!

Saturday, July 13, 2013

Not everyone is a professional chemist

Not everyone is a professional chemist, so pool experts recommend you see them first for any problems you encounter. You can head off the issues by taking water samples to the local pool store once a month. “It’s like going to a doctor for a checkup, still want to try it the hands-on way? Here are the reasons behind and quick fixes for the most common pool problems. ALGAE AFFLICTION DESCRIPTION: Probably the most common of pool problems. The surface of the pool is green and swimmers merge looking like swamp monsters. CAUSE: Algae has infested the pool. “90% of the time the cause is that the chlorine level is low SOLUTION: Shock that pool! Perform a shock treatment using three times the normal amount of shock. Couple that with algaecide and the algae will be exterminated. CLOGGED FILTER DESCRIPTION: The pool is starting to build unseemly debris and the filter, when examined, is chock full. CAUSE: Relax; this one is a good thing. It pretty much means the filter is doing its job it’s clogged because the pool was dirty. SOLUTION: Perform some filter maintenance; clean it out each time it’s clogged. At least once a year it should be chemically cleaned to ensure its long functional life, according to. FOAMING FRUSTRATION DESCRIPTION: The pool looks like it is trying to host a foam party and you are not amused. White suds can be seen on the surface. CAUSE: “Most of the foaming we see in pools is from the use of poor algaecide, how do you spot one of these poor algaecides? “They never say “This is a foaming algaecide, “They’re cheaper and, not to pick on anybody, but you see them most often at mass marketers.” SOLUTION: Head back to the store and get an anti-foam agent and be sure to buy future algaecide from a trustworthy pool dealer who can vouch for it. MINERAL MISHAP DESCRIPTION: The pool is either a milk chocolate brown, or a brilliant beautiful teal. Blondes may leave the water with their fair locks green. CAUSE: An abundance of minerals in the water is the root of the problem. Pools with a lot of iron go the brown route, those with more copper take on the teal look with the green hair effect. SOLUTION: Pool stores have different chemicals to remove different minerals from the water, so purchase and use the one that is right for the pool. MURKY WATER DILEMMA DESCRIPTION: The bottom of the pool is a mystery. What could be lurking in its depths? Nobody knows. CAUSE: Improper pH levels, is the traditional cause - and the rain aided the problem. The rain is really acidic in this area and it does affect the pools. SOLUTION: Test the water’s pH levels and adjust accordingly. STAIN AGITATION DESCRIPTION: There is a weird brown stain on the pool’s walls or floor and no one knows where it came from. CAUSE: It could be organic, or the result of high mineral levels (see mineral mishap). Test the water to see by using a sock. First, put a little pH decreaser in the sock, then rub it on the stain. If it removes the stain, make a note of it. If it does not remove the stain, try again but with a chlorine stick in the sock instead of pH decreaser. SOLUTION: This is one for the professionals, present the results of the test to them and let them have at. But do it quickly, as removing the stain may not be possible. “It’s like your favorite article of clothing that gets stained. The longer it’s left untreated, the harder the stain will be to get out. For more help go to WWW.POOLHELPUSA.COM

Wednesday, December 26, 2012

Clean Up A Green Pool



FROM GREEN TO CLEAN
To clean murky and green pool water, follow these steps:
First and foremost make sure you have good flow. Clean your filter and all your baskets.
Test your water with a good test kit and write down the results.
Balance your water. If your alkalinity is low, you are running the risk of staining your pool and try to make sure your PH is within the guidelines 7.2-7.8 is a good range.
Then, use a shock or chlorine to shock the pool. When you buy these products ask someone that works there ( Or read the directions carefully). The ones that have been found to work best require you to shock with the treatment.
After that, run your filter 24 hours and test it again. The shock will bring your chlorine level down so you must make sure it does not get too low. At this point your water may be cloudy or you may have a lot of dead algae on the floor.
Vacuum up that algae and clean that filter out. If the water is cloudy use the directions below. Just keep cleaning that filter out until that water is clear.
You must then balance all of your pool chemicals to maintain the pool in good condition.
These are your main concerns and should be kept within these ranges.
Chlorine 1-3 ppm
Alkalinity 80-120
PH 7.2 7.8
Stabilizer 40-80
Calcium 200-275
Then test your pool weekly to ensure correct chemical levels.
There are many ways to clear a pool and many different opinions on how to do it however Chlorine is one of the best ways to do this.
If your not a fan of chlorine you could use algaecide.
To kill the algae, use lots of, algaecide etc.
Coagulate the dead algae into large clumps. Pool supply stores sell a spray coagulator that attaches to a garden hose. Spray it over the pool and let it sit overnight.
Add diatomaceous earth to the filter. This white powder is sold in pool stores and used to be necessary before cartridges became affordable. Add a lot. This coats the filter and makes it impermeable, even to algae-sized particles.
Once clear you may want to prevent the pool from turning green again and keeping the pool within those guides set out above should do that however some pools are just problem pools in this case I would advise a prevention type product to help keep the pool clean.